All articles

How to Compare Contractor Bids for Your Outdoor Project

How to Compare Contractor Bids for Your Outdoor Project

To compare contractor bids fairly, make sure every contractor priced the same work, then lay the bids side by side line by line. Check scope, materials, allowances, schedule, payment terms and credentials before you look at the bottom line. Two bids with a $4,000 gap often describe two different jobs. This guide shows how to get bids you can compare, how to read them, and how to decide.

Propertyimprovementestimator
Make Outdoor Bids Easier to Compare
Map your project dimensions and elements before requesting quotes, so contractors can assess a clearer, more specific scope.

TL;DR

  • Give every contractor the same written scope, with dimensions and materials, so the bids describe one job.
  • Compare line items, not totals. Treat allowances and exclusions as open questions.
  • A bid far below the others often signals a mistake or omitted work, so ask about it before you accept.
  • Verify license and insurance, and never pay the full price up front.

Table of Contents

Why contractor quotes vary so much

The same fence or deck can come back at wildly different prices. Often the contractors are not pricing the same thing. Virginia’s licensing agency notes that bids can differ because one includes higher-quality materials or more extensive work, and that a substantially lower bid may contain a mistake or leave work out.

A hardscape trade association adds that labor may be the biggest expense and complexity drives cost. Landscape contractors also point out that variation is rarely just overcharging. It usually comes from unclear scope, different materials and different experience.

Common causes in outdoor work:

  • Vague measurements. One contractor eyeballs 140 linear feet of fence, another measures 165.
  • Different materials. Pressure-treated pine versus cedar, or a 4-inch versus 6-inch concrete slab.
  • Site conditions. Slope, rock, access for equipment, tree roots, and utility locations.
  • Hidden assumptions. Who pulls the permit, hauls away debris, or restores the lawn.
  • Business model. Overhead, crew size, insurance, and how busy the contractor is.

Start by getting bids you can actually compare

The comparison is won or lost before any bid arrives. The Illinois Attorney General’s consumer guidance says to write down exactly what you want done, including timeframe, materials, payment method and payment schedule, and to get estimates based on the same work.

Write one scope and send it to everyone

A useful outdoor scope includes:

  1. Location and dimensions of each element (fence run, deck footprint, pool outline, slab size).
  2. Materials and finish, by name where you can: species of wood, post size, concrete thickness, railing type.
  3. Site notes: slope, gates, access width, existing structures to remove, utilities nearby.
  4. Who handles permits, cleanup, debris haul-off and restoration.
  5. Your target timeframe and preferred payment structure.
  6. Photos of the area.

If you want a template for what to include, see our guide to what a landscaping scope of work should include and the five documents in a contractor bid package.

Draw the project instead of describing it

Words leave room for guesswork. A drawing on aerial imagery does not. With our Fence Estimator, Deck Estimator or Pool Estimator, you draw the project on your actual property, and every contractor receives the same measurements, options and photos. That removes the biggest source of mismatched bids: each contractor measuring and assuming differently.

How many bids?

Three is a common target. The hardscape association describes three proposals as a budget reality check. Fewer gives you little to compare. Many more becomes hard to manage and wastes contractors’ time. If the three come back wildly different, add a fourth after you have clarified the scope, not before.

Three-bid comparison and when to request another

Estimate vs. quote: know what you are holding

A rough estimate and a firm quote are not the same document. Early estimates are ballparks and can move. A fixed quote commits to a price for a defined scope. Our explainer on quote vs. estimate covers the difference. Also check whether the price is fixed or billed by time and materials. Our time and materials vs. fixed price playbook explains how that affects risk. Do not compare an open-ended hourly estimate to a fixed quote as if they were equal.

Build a comparison sheet

Put the bids in one table. Here is a layout that works for a deck, fence or patio project:

Item Bid A Bid B Bid C
Total price
Measurements used
Materials (brand, grade, size)
Demolition and haul-off
Permits (who pulls, who pays)
Allowances and amounts
Exclusions
Start date and duration
Payment schedule
Warranty (labor and materials)
License and insurance verified

Fill every cell. A blank cell is a question for that contractor. The FTC says a written estimate should describe the work, materials, completion date and price, so a bid that cannot fill these cells is incomplete.

Worked example: three fence bids

Suppose you ask for 150 feet of 6-foot wood privacy fence with one gate. The bids look like this:

  • Bid A, $6,200: cedar boards, 4x4 posts, gate included, old fence removal included.
  • Bid B, $4,900: pressure-treated boards, 4x4 posts, gate included, removal extra.
  • Bid C, $3,800: pressure-treated, no gate listed, 130 feet measured, no removal.

These figures are illustrative, not market prices. Bid C looks cheapest, but it covers less fence, no gate and no removal. Once you add those, it may land near Bid B. The right move is to send each contractor a corrected scope and ask them to re-price, not to pick the lowest number.

Read allowances and exclusions closely

An allowance is a placeholder amount for something not yet selected, such as railing style or a light fixture package. Treat it as an open question. If one bid allows $1,000 for materials and another allows $3,500, the totals are not comparable until you align them.

Ask each contractor:

  • What is in the allowance, and what happens if my choice costs more or less?
  • What is excluded: grading, drainage, permits, electrical, irrigation repair, sod?
  • What conditions would trigger a change order, and how is it priced and approved?
  • Why is your price higher or lower than a competing bid for the same scope? The FTC advises asking contractors to explain large differences among estimates.

An FTC contractor guide also suggests a broom clause, which makes the contractor responsible for cleanup, including spills and stains. It is a small line that prevents a big argument.

For sport courts, where site prep varies widely, see our walkthroughs of sport court bids and the line items that should match.

Compare the contractor, not just the number

A good price from the wrong contractor is expensive. The Illinois guidance says to compare work, materials, warranties, timetables, total price and payment schedule, and also to check licensing, complaint records, references, permits and subcontractors.

Before accepting any bid:

  • License. The FTC advises checking that the license is current where licensing is required. Rules differ by state, so look up your state licensing board. In Idaho and Utah, start with the state’s contractor licensing division.
  • Insurance. Ask for current certificates of insurance directly from the insurer. Our guide to questions to ask contractors and the COI to request lists what to request.
  • References and photos. Ask for recent jobs similar to yours, and call at least two.
  • Subcontractors. Ask who actually does the work on your property.

A walkthrough of finding and verifying a licensed professional with your state board shows the same steps, and they apply to any trade.

Red flags in low, high or vague bids

  • A much lower price. Probably a mistake or missing work, per Virginia’s licensing agency. Ask line by line what differs.
  • A much higher price. It may reflect premium materials, a tougher site read, or a contractor with a full schedule. Ask what drives it before you dismiss it.
  • Pressure to decide now, cash-only terms, or a request that you pull the permits yourself. The FTC lists these as warning signs.
  • Large up-front payments. The FTC says not to pay the full price up front or make final payment before you are satisfied. Deposit limits vary by state, so check your state or local consumer agency.
  • A one-line bid. “Install deck, $9,000” gives you nothing to compare and nothing to enforce.

If a bid is unusually high or low, the logic in a guide to understanding brush removal quotes applies to any trade: find out what is included before judging the price.

Perspective: what we see in mismatched bids

We built our platform around one observation: most bid problems start with the request, not the contractor. When a homeowner describes a project in a few sentences, each contractor fills the gaps differently, and the bids come back impossible to compare. Measuring the project on aerial imagery, listing options and attaching photos gives every bidder identical information. Contractors also spend less time on guesswork, so their quotes tend to be tighter.

Our advice is to settle scope first, get a local price range second, and only then collect bids. A range based on your dimensions and local cost data tells you whether a bid is realistic before you ever sit down with a contractor. Our pricing methodology explains how those ranges are built, and our guide on getting accurate project estimates walks through the process.

— Christian

Plan the project first, then request bids

If you are planning a fence, deck, pool, concrete pad, asphalt, sport court or retaining wall, you can map it on your property and see a site-specific price range with no account required. Then you can send a detailed quote request so contractors price the same drawn scope.

Propertyimprovementestimator

Start on our Property Improvement Estimator or get a local project report for your address.

Making the final decision

When the sheet is complete and the bids describe the same job:

  1. Throw out any bid that cannot be made comparable after clarification.
  2. Rank the rest on scope clarity, credentials, references, schedule and warranty.
  3. Use price as the tiebreaker among contractors you trust, not as the first filter.
  4. Put everything in a written contract: work, materials, warranties, timetable, total price and payment schedule.
  5. Tie payments to progress, and hold the last payment until the work is done to your satisfaction.

A guide to comparing proposals beyond price makes the same point: match bids to the same project requirements before weighing cost.

FAQ

Should I always reject the highest and lowest bids?

No. Look at why they differ. The lowest may omit work, and the highest may include better materials or a more careful process. Ask both contractors to walk through their numbers against your scope.

How many contractor quotes should I get?

Three is a practical number for most outdoor projects. It gives you a sense of the market without overwhelming you. If the bids are far apart, clarify your scope and request updated quotes before adding more bidders.

What if a contractor refuses to itemize?

Treat that as a warning. A written estimate should describe the work, materials, completion date and price. Without an itemized breakdown you cannot compare bids or hold anyone to the scope.

Is a quote the same as an estimate?

Not necessarily. An estimate is often an approximation that can change, while a quote or fixed-price bid commits to a number for a defined scope. Ask which one you have, and what would cause the price to change.

Sources

Ready to price the project on your property?

Use the article as context, then draw the actual layout on the map.

Open the estimator